System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1) Copyright (c) 2000 by cisco Systems, Inc. cisco 2620 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory Self decompressing the image : ########################################################################## [OK] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 27-Apr-04 19:01 by miwang cisco 2620 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory . Processor board ID JAD05190MTZ (4292891495) M860 processor: part number 0, mask 49 Bridging software. X.25 software, Version 3.0.0. 1 FastEthernet/IEEE 802.3 interface(s) 32K bytes of non-volatile configuration memory. 16384K bytes of processor board System flash (Read/Write) --- System Configuration Dialog --- Continue with configuration dialog? [yes/no]: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1) Copyright (c) 2000 by cisco Systems, Inc. cisco 2620 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory Self decompressing the image : ########################################################################## [OK] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 27-Apr-04 19:01 by miwang cisco 2620 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory . Processor board ID JAD05190MTZ (4292891495) M860 processor: part number 0, mask 49 Bridging software. X.25 software, Version 3.0.0. 1 FastEthernet/IEEE 802.3 interface(s) 1 Low-speed serial(sync/async) network interface(s) 32K bytes of non-volatile configuration memory. 16384K bytes of processor board System flash (Read/Write) --- System Configuration Dialog --- Continue with configuration dialog? [yes/no]: n Press RETURN to get started! Router>enable Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#show config ^ % Invalid input detected at '^' marker. Router(config)#do show config show config ^ % Invalid input detected at '^' marker. Router(config)#do show star Router(config)#do show star Router(config)#do show start Router(config)#do show start Router(config)#do show start Router(config)#do show startu Router(config)#^Z %SYS-5-CONFIG_I: Configured from console by console Router#show start Router#show startup-config Router#show startup-config Router#show startup-config startup-config is not present Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#interface se Router(config)#interface serial 0/0 Router(config-if)#ip address 192.168.1.254 255.255.255.0 Router(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/0, changed state to down Router(config-if)#clockra Router(config-if)#cloc Router(config-if)#clock ? rate Configure serial interface clock speed Router(config-if)#clock ? rate Configure serial interface clock speed Router(config-if)#clock rate Router(config-if)#clock rate 64000 Router(config-if)# %LINK-5-CHANGED: Interface Serial0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up Router(config-if)#^Z %SYS-5-CONFIG_I: Configured from console by console Router#show interface FastEthernet0/0 is administratively down, line protocol is down (disabled) Hardware is Lance, address is 0006.2ae0.9b97 (bia 0006.2ae0.9b97) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set ARP type: ARPA, ARP Timeout 04:00:00, Last input 00:00:08, output 00:00:05, output hang never Last clearing of "show interface" counters never Queueing strategy: fifo Output queue :0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Serial0/0 is up, line protocol is up (connected) Hardware is HD64570 Internet address is 192.168.1.254/24 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive set (10 sec) Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0 (size/max/drops); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/0/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#inter Router(config)#interface fa0/0 Router(config-if)#ip address 192.168.2.252 255.255.255.0 Router(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Router(config-if)#copy run start ^ % Invalid input detected at '^' marker. Router(config-if)#^Z %SYS-5-CONFIG_I: Configured from console by console Router#copy run start Destination filename [startup-config]? Building configuration... [OK] Router# Router con0 is now available Press RETURN to get started. Router>enable Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#show ip route ^ % Invalid input detected at '^' marker. Router(config)#show ? % Unrecognized command Router(config)#show ^Z %SYS-5-CONFIG_I: Configured from console by console Router#show ? access-lists List access lists arp Arp table cdp CDP information clock Display the system clock controllers Interface controllers status crypto Encryption module debugging State of each debugging option dhcp Dynamic Host Configuration Protocol status flash: display information about flash: file system frame-relay Frame-Relay information history Display the session command history hosts IP domain-name, lookup style, nameservers, and host table interfaces Interface status and configuration ip IP information ospf For OSPF debug only ospfv3 For OSPFv3 debug only processes Active process statistics protocols Active network routing protocols running-config Current operating configuration sessions Information about Telnet connections ssh Status of SSH server connections startup-config Contents of startup configuration Router#show ip ? access-lists List access lists arp IP ARP table dhcp Show items in the DHCP database eigrp IP-EIGRP show commands interface IP interface status and configuration nat IP NAT information ospf OSPF information protocols IP routing protocol process parameters and statistics rip IP RIP show commands route IP routing table ssh Information on SSH Router#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set C 192.168.1.0/24 is directly connected, Serial0/0 C 192.168.2.0/24 is directly connected, FastEthernet0/0 Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#router ? eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) ospf Open Shortest Path First (OSPF) rip Routing Information Protocol (RIP) Router(config)#router rip Router(config-router)#version ? <1-2> version Router(config-router)#version 2 Router(config-router)#network ? A.B.C.D Network number Router(config-router)#network % Incomplete command. Router(config-router)#network 192.168.1.0 192.168.2.0 ^ % Invalid input detected at '^' marker. Router(config-router)#network 192.168.1.0 Router(config-router)#network 192.168.2.0 Router(config-router)#network 192.168.3.0 Router(config-router)#^Z %SYS-5-CONFIG_I: Configured from console by console Router#show router ^ % Invalid input detected at '^' marker. Router#show route ^ % Invalid input detected at '^' marker. Router#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set C 192.168.1.0/24 is directly connected, Serial0/0 C 192.168.2.0/24 is directly connected, FastEthernet0/0 R 192.168.3.0/24 [120/1] via 192.168.1.253, 00:00:12, Serial0/0 Router#